Cypress Computer Hardware STK11C88 User Manual

STK11C88  
256 Kbit (32K x 8) SoftStore nvSRAM  
Features  
Functional Description  
25 ns and 45 ns access times  
The Cypress STK11C88 is a 256 Kb fast static RAM with a  
nonvolatile element in each memory cell. The embedded  
nonvolatile elements incorporate QuantumTraptechnology  
producing the world’s most reliable nonvolatile memory. The  
SRAM provides unlimited read and write cycles, while  
independent, nonvolatile data resides in the highly reliable  
QuantumTrap cell. Data transfers under Software control from  
SRAM to the nonvolatile elements (the STORE operation). On  
power up, data is automatically restored to the SRAM (the  
RECALL operation) from the nonvolatile memory. RECALL  
operations are also available under software control.  
Pin compatible with industry standard SRAMs  
Software initiated STORE and RECALL  
Automatic RECALL to SRAM on power up  
Unlimited Read and Write endurance  
Unlimited RECALL cycles  
1,000,000 STORE cycles  
100 year data retention  
Single 5V+10% power supply  
Commercial and Industrial Temperatures  
28-pin (300 mil and 330 mil) SOIC packages  
RoHS compliance  
Logic Block Diagram  
Cypress Semiconductor Corporation  
Document Number: 001-50591 Rev. **  
198 Champion Court  
San Jose, CA 95134-1709  
408-943-2600  
Revised January 29, 2009  
 
STK11C88  
1. Read address 0x0E38, Valid READ  
2. Read address 0x31C7, Valid READ  
3. Read address 0x03E0, Valid READ  
4. Read address 0x3C1F, Valid READ  
5. Read address 0x303F, Valid READ  
Device Operation  
The STK11C88 is a versatile memory chip that provides several  
modes of operation. The STK11C88 can operate as a standard  
32K x 8 SRAM. A 32K x 8 array of nonvolatile storage elements  
shadow the SRAM. SRAM data can be copied from nonvolatile  
memory or nonvolatile data can be recalled to the SRAM.  
6. Read address 0x0FC0, Initiate STORE cycle  
The software sequence is clocked with CE controlled READs.  
When the sixth address in the sequence is entered, the STORE  
cycle commences and the chip is disabled. It is important that  
READ cycles and not WRITE cycles are used in the sequence.  
It is not necessary that OE is LOW for a valid sequence. After the  
tSTORE cycle time is fulfilled, the SRAM is again activated for  
READ and WRITE operation.  
SRAM Read  
The STK11C88 performs a READ cycle whenever CE and OE  
are LOW, while WE is HIGH. The address specified on pins  
A0–14 determines the 32,768 data bytes accessed. When the  
READ is initiated by an address transition, the outputs are valid  
after a delay of tAA (READ cycle 1). If the READ is initiated by  
CE or OE, the outputs are valid at tACE or at tDOE, whichever is  
later (READ cycle 2). The data outputs repeatedly respond to  
address changes within the tAA access time without the need for  
transitions on any control input pins, and remain valid until  
another address change or until CE or OE is brought HIGH.  
Software RECALL  
Data is transferred from the nonvolatile memory to the SRAM by  
a software address sequence. A software RECALL cycle is  
initiated with a sequence of READ operations in a manner similar  
to the software STORE initiation. To initiate the RECALL cycle,  
the following sequence of CE controlled READ operations is  
performed:  
SRAM Write  
A WRITE cycle is performed whenever CE and WE are LOW.  
The address inputs must be stable prior to entering the WRITE  
cycle and must remain stable until either CE or WE goes HIGH  
at the end of the cycle. The data on the common IO pins DQ0–7  
are written into the memory if it has valid tSD, before the end of  
a WE controlled WRITE or before the end of an CE controlled  
WRITE. Keep OE HIGH during the entire WRITE cycle to avoid  
data bus contention on common IO lines. If OE is left LOW,  
internal circuitry turns off the output buffers tHZWE after WE goes  
LOW.  
1. Read address 0x0E38, Valid READ  
2. Read address 0x31C7, Valid READ  
3. Read address 0x03E0, Valid READ  
4. Read address 0x3C1F, Valid READ  
5. Read address 0x303F, Valid READ  
6. Read address 0x0C63, Initiate RECALL cycle  
Internally, RECALL is a two step procedure. First, the SRAM data  
is cleared, and then the nonvolatile information is transferred into  
the SRAM cells. After the tRECALL cycle time, the SRAM is once  
again ready for READ and WRITE operations. The RECALL  
operation does not alter the data in the nonvolatile elements. The  
nonvolatile data can be recalled an unlimited number of times.  
Software STORE  
Data is transferred from the SRAM to the nonvolatile memory by  
a software address sequence. The STK11C88 software STORE  
cycle is initiated by executing sequential CE controlled READ  
cycles from six specific address locations in exact order. During  
the STORE cycle, an erase of the previous nonvolatile data is  
first performed, followed by a program of the nonvolatile  
elements. When a STORE cycle is initiated, input and output are  
disabled until the cycle is completed.  
Hardware RECALL (Power Up)  
During power up or after any low power condition (VCC<VRESET),  
an internal RECALL request is latched. When VCC once again  
exceeds the sense voltage of VSWITCH, a RECALL cycle is  
automatically initiated and takes tHRECALL to complete.  
Because a sequence of READs from specific addresses is used  
for STORE initiation, it is important that no other READ or WRITE  
accesses intervene in the sequence. If they intervene, the  
sequence is aborted and no STORE or RECALL takes place.  
If the STK11C88 is in a WRITE state at the end of power up  
RECALL, the SRAM data is corrupted. To help avoid this  
situation, a 10 Kohm resistor is connected either between WE  
To initiate the software STORE cycle, the following READ  
sequence is performed:  
and system VCC or between CE and system VCC  
.
Document Number: 001-50591 Rev. **  
Page 3 of 15  
 
STK11C88  
Figure 3. Icc (max) Writes  
Hardware Protect  
The STK11C88 offers hardware protection against inadvertent  
STORE operation and SRAM WRITEs during low voltage  
conditions. When VCC<VSWITCH  
,
all externally initiated  
STORE operations and SRAM WRITEs are inhibited.  
Noise Considerations  
The STK11C88 is a high speed memory. It must have a high  
frequency bypass capacitor of approximately 0.1 µF  
connected between VCC and VSS, using leads and traces that  
are as short as possible. As with all high speed CMOS ICs,  
careful routing of power, ground, and signals help prevent  
noise problems.  
Low Average Active Power  
CMOS technology provides the STK11C88 the benefit of  
drawing significantly less current when it is cycled at times  
longer than 50 ns. Figure 2 and Figure 3 show the relationship  
between ICC and READ or WRITE cycle time. Worst case  
current consumption is shown for both CMOS and TTL input  
levels (commercial temperature range, VCC = 5.5V, 100  
percent duty cycle on chip enable). Only standby current is  
drawn when the chip is disabled. The overall average current  
drawn by the STK11C88 depends on the following items:  
Best Practices  
nvSRAM products have been used effectively for over 15  
years. While ease-of-use is one of the product’s main system  
values, the experience gained working with hundreds of appli-  
cations has resulted in the following suggestions as best  
practices:  
1. The duty cycle of chip enable  
2. The overall cycle rate for accesses  
3. The ratio of READs to WRITEs  
4. CMOS versus TTL input levels  
5. The operating temperature  
6. The VCC level  
The nonvolatile cells in a nvSRAM are programmed on the  
test floor during final test and quality assurance. Incoming  
inspection routines at customer or contract manufacturer’s  
sites, sometimes, reprogram these values. Final NV patterns  
are typically repeating patterns of AA, 55, 00, FF, A5, or 5A.  
The end product’s firmware should not assume that a NV  
array is in a set programmed state. Routines that check  
memory content values to determine first time system config-  
uration and cold or warm boot status, should always program  
a unique NV pattern (for example, a complex 4-byte pattern  
of 46 E6 49 53 hex or more random bytes) as part of the final  
system manufacturing test to ensure these system routines  
work consistently.  
7. IO loading  
Figure 2. Icc (max) Reads  
Power up boot firmware routines should rewrite the nvSRAM  
into the desired state. While the nvSRAM is shipped in a  
preset state, best practice is to again rewrite the nvSRAM  
into the desired state as a safeguard against events that  
might flip the bit inadvertently (program bugs or incoming  
inspection routines).  
Document Number: 001-50591 Rev. **  
Page 4 of 15  
 
   
STK11C88  
Table 2. Software STORE/RECALL Mode Selection  
A13 – A0  
Mode  
IO  
Notes  
CE  
L
WE  
H
0x0E38  
0x31C7  
0x03E0  
0x3C1F  
0x303F  
0x0FC0  
Read SRAM  
Read SRAM  
Read SRAM  
Read SRAM  
Read SRAM  
Output Data  
Output Data  
Output Data  
Output Data  
Output Data  
Output Data  
Nonvolatile STORE  
L
H
0x0E38  
0x31C7  
0x03E0  
0x3C1F  
0x303F  
0x0C63  
Read SRAM  
Read SRAM  
Read SRAM  
Read SRAM  
Read SRAM  
Output Data  
Output Data  
Output Data  
Output Data  
Output Data  
Output Data  
Nonvolatile RECALL  
Notes  
1. The six consecutive addresses must be in the order listed. WE must be high during all six consecutive CE controlled cycles to enable a nonvolatile cycle.  
2. While there are 15 addresses on the STK11C88, only the lower 14 are used to control software modes.  
Document Number: 001-50591 Rev. **  
Page 5 of 15  
 
   
STK11C88  
Voltage on DQ0-7 ...................................–0.5V to Vcc + 0.5V  
Power Dissipation ......................................................... 1.0W  
DC Output Current (1 output at a time, 1s duration).... 15 mA  
Maximum Ratings  
Exceeding maximum ratings may shorten the useful life of the  
device. These user guidelines are not tested.  
Storage Temperature .................................65°C to +150°C  
Temperature under bias..............................55°C to +125°C  
Supply Voltage on VCC Relative to GND.......... –0.5V to 7.0V  
Voltage on Input Relative to Vss............–0.6V to VCC + 0.5V  
Operating Range  
Range  
Commercial  
Industrial  
Ambient Temperature  
0°C to +70°C  
VCC  
4.5V to 5.5V  
4.5V to 5.5V  
-40°C to +85°C  
DC Electrical Characteristics  
Over the operating range (VCC = 4.5V to 5.5V)  
Parameter  
ICC1  
Description  
Test Conditions  
Min  
Max Unit  
Average VCC Current tRC = 25 ns  
Commercial  
Industrial  
97  
70  
mA  
mA  
t
RC = 45 ns  
Dependent on output loading and cycle rate.  
Values obtained without output loads.  
100  
70  
mA  
mA  
I
OUT = 0 mA.  
Average VCC Current All Inputs Do Not Care, VCC = Max  
during STORE Average current for duration tSTORE  
Average VCC Current WE > (VCC – 0.2V). All other inputs cycling.  
ICC2  
ICC3  
3
mA  
mA  
10  
at tRC= 200 ns, 5V,  
25°C Typical  
Dependent on output loading and cycle rate. Values obtained  
without output loads.  
[3]  
ISB1  
Average VCC Current tRC=25ns, CE > VIH  
Commercial  
30  
22  
mA  
mA  
μA  
(Standby, Cycling  
TTL Input Levels)  
tRC=45ns, CE > VIH  
Industrial  
31  
23  
[3]  
ISB2  
VCC Standby Current CE > (VCC – 0.2V). All others VIN < 0.2V or > (VCC – 0.2V).  
(Standby, Stable  
750  
CMOS Input Levels)  
IIX  
Input Leakage  
Current  
VCC = Max, VSS < VIN < VCC  
-1  
-5  
+1  
+5  
μA  
μA  
V
IOZ  
VIH  
VIL  
Off State Output  
Leakage Current  
VCC = Max, VSS < VIN < VCC, CE or OE > VIH or WE < VIL  
Input HIGH Voltage  
2.2  
VCC  
0.5  
+
Input LOW Voltage  
VSS  
0.5  
0.8  
V
VOH  
VOL  
Output HIGH Voltage IOUT = –4 mA  
Output LOW Voltage IOUT = 8 mA  
2.4  
V
V
0.4  
Data Retention and Endurance  
Parameter  
DATAR  
Description  
Min  
100  
Unit  
Data Retention  
Years  
K
NVC  
Nonvolatile STORE Operations  
1,000  
Note  
3. CE > V will not produce standby current levels until any nonvolatile cycle in progress has timed out.  
IH  
Document Number: 001-50591 Rev. **  
Page 6 of 15  
 
 
STK11C88  
Capacitance  
In the following table, the capacitance parameters are listed.[4]  
Parameter  
Description  
Input Capacitance  
Output Capacitance  
Test Conditions  
TA = 25°C, f = 1 MHz,  
CC = 0 to 3.0 V  
Max  
5
Unit  
pF  
CIN  
V
COUT  
7
pF  
Thermal Resistance  
In the following table, the thermal resistance parameters are listed.[4]  
28-SOIC  
(300 mil)  
28-SOIC  
(330 mil)  
Parameter  
Description  
Test Conditions  
Unit  
ΘJA  
Thermal Resistance  
(Junction to Ambient)  
Test conditions follow standard test methods and  
procedures for measuring thermal impedance,  
per EIA / JESD51.  
TBD  
TBD  
°C/W  
ΘJC  
Thermal Resistance  
(Junction to Case)  
TBD  
TBD  
°C/W  
Figure 4. AC Test Loads  
R1 480Ω  
5.0V  
Output  
R2  
30 pF  
255Ω  
AC Test Conditions  
Input Pulse Levels..................................................0 V to 3 V  
Input Rise and Fall Times (10% - 90%)........................ <5 ns  
Input and Output Timing Reference Levels................... 1.5 V  
Note  
4. These parameters are guaranteed by design and are not tested.  
Document Number: 001-50591 Rev. **  
Page 7 of 15  
 
 
STK11C88  
AC Switching Characteristics  
SRAM Read Cycle  
Parameter  
25 ns  
45 ns  
Description  
Unit  
Cypress  
Alt  
Min  
Max  
Min  
Max  
Parameter  
tACE  
tELQV  
tAVAV, ELEH  
tAVQV  
Chip Enable Access Time  
Read Cycle Time  
25  
45  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
tRC  
t
25  
45  
[6]  
tAA  
tDOE  
Address Access Time  
25  
10  
45  
20  
tGLQV  
Output Enable to Data Valid  
Output Hold After Address Change  
Chip Enable to Output Active  
Chip Disable to Output Inactive  
Output Enable to Output Active  
Output Disable to Output Inactive  
Chip Enable to Power Active  
Chip Disable to Power Standby  
[6]  
tOHA  
tAXQX  
5
5
5
5
[7]  
[7]  
[7]  
[7]  
tLZCE  
tHZCE  
tLZOE  
tHZOE  
tELQX  
tEHQZ  
10  
10  
25  
15  
15  
45  
tGLQX  
0
0
0
0
tGHQZ  
[4]  
tPU  
tELICCH  
tEHICCL  
[4]  
tPD  
Switching Waveforms  
Figure 5. SRAM Read Cycle 1: Address Controlled [5, 6]  
W5&  
$''5(66  
W$$  
W2+$  
'4ꢌꢊ'$7$ꢌ287ꢋ  
'$7$ꢌ9$/,'  
Figure 6. SRAM Read Cycle 2: CE and OE Controlled [5]  
W5&  
$''5(66  
&(  
W$&(  
W3'  
W+=&(  
W/=&(  
2(  
W+=2(  
W'2(  
W/=2(  
'4ꢌꢊ'$7$ꢌ287ꢋ  
'$7$ꢌ9$/,'  
$&7,9(  
W38  
67$1'%<  
,&&  
Notes  
5. WE must be HIGH during SRAM Read Cycles and LOW during SRAM WRITE cycles.  
6. I/O state assumes CE and OE < V and WE > V ; device is continuously selected.  
IL  
IH  
7. Measured ±200 mV from steady state output voltage.  
Document Number: 001-50591 Rev. **  
Page 8 of 15  
 
     
STK11C88  
SRAM Write Cycle  
Parameter  
25 ns  
45 ns  
Description  
Write Cycle Time  
Unit  
Cypress  
Alt  
Min  
Max  
Min  
Max  
Parameter  
tWC  
tAVAV  
tWLWH, WLEH  
tELWH, ELEH  
tDVWH, DVEH  
tWHDX, EHDX  
tAVWH, AVEH  
tAVWL, AVEL  
tWHAX, EHAX  
tWLQZ  
tWHQX  
25  
20  
20  
10  
0
45  
30  
30  
15  
0
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
ns  
tPWE  
tSCE  
tSD  
t
Write Pulse Width  
t
Chip Enable To End of Write  
Data Setup to End of Write  
Data Hold After End of Write  
Address Setup to End of Write  
Address Setup to Start of Write  
Address Hold After End of Write  
Write Enable to Output Disable  
Output Active After End of Write  
t
tHD  
tAW  
tSA  
tHA  
t
t
20  
0
30  
0
t
t
0
0
[7,8]  
tHZWE  
tLZWE  
10  
15  
5
5
Switching Waveforms  
Figure 7. SRAM Write Cycle 1: WE Controlled [9]  
tWC  
ADDRESS  
CE  
tHA  
tSCE  
tAW  
tSA  
tPWE  
WE  
tHD  
tSD  
DATA VALID  
DATA IN  
tHZWE  
tLZWE  
HIGH IMPEDANCE  
PREVIOUS DATA  
DATA OUT  
Figure 8. SRAM Write Cycle 2: CE Controlled [9]  
tWC  
ADDRESS  
tHA  
tSCE  
tSA  
CE  
WE  
tAW  
tPWE  
tSD  
tHD  
DATA IN  
DATA VALID  
HIGH IMPEDANCE  
DATA OUT  
Notes  
8. If WE is Low when CE goes Low, the outputs remain in the high impedance state.  
9.  
CE or WE must be greater than V during address transitions.  
IH  
Document Number: 001-50591 Rev. **  
Page 9 of 15  
 
   
STK11C88  
STORE INHIBIT or Power Up RECALL  
STK11C88  
Parameter  
Alt  
Description  
Unit  
Min  
Max  
tHRECALL  
tRESTORE  
tHLHZ  
Power up RECALL Duration  
STORE Cycle Duration  
550  
10  
μs  
ms  
V
[6]  
tSTORE  
VRESET  
Low Voltage Reset Level  
Low Voltage Trigger Level  
3.6  
4.5  
VSWITCH  
4.0  
V
Switching Waveforms  
Figure 9. STORE INHIBIT/Power Up RECALL  
VCC  
5V  
VSWITCH  
VRESET  
STORE INHIBIT  
POWER-UP RECALL  
t
HRECALL  
DQ (DATA OUT)  
POWER-UP  
RECALL  
BROWN OUT  
STORE INHIBIT  
BROWN OUT  
STORE INHIBIT  
BROWN OUT  
STORE INHIBIT  
NO RECALL  
NO RECALL  
RECALL WHEN  
(V DID NOT GO  
(V DID NOT GO  
V
RETURNS  
CC  
CC  
CC  
BELOW V  
)
BELOW V  
)
ABOVE V  
RESET  
RESET  
SWITCH  
Notes  
10. t  
starts from the time V rises above V .  
SWITCH  
HRECALL  
CC  
Document Number: 001-50591 Rev. **  
Page 10 of 15  
 
 
STK11C88  
Software Controlled STORE/RECALL Cycle  
The software controlled STORE/RECALL cycle follows. [11, 12]  
25 ns  
45 ns  
Parameter  
tRC  
Alt  
Description  
Unit  
Min  
25  
0
Max  
Min  
45  
0
Max  
tAVAV  
tAVEL  
tELEH  
tELAX  
STORE/RECALL Initiation Cycle Time  
Address Setup Time  
ns  
ns  
ns  
ns  
μs  
[11]  
tSA  
tCW  
Clock Pulse Width  
20  
20  
30  
20  
[11]  
tHACE  
Address Hold Time  
tRECALL  
RECALL Duration  
20  
20  
Switching Waveforms  
Figure 10. CE Controlled Software STORE/RECALL Cycle [12]  
tRC  
tRC  
ADDRESS # 1  
ADDRESS # 6  
ADDRESS  
CE  
tSA  
tSCE  
tHACE  
OE  
t
STORE / tRECALL  
HIGH IMPEDANCE  
DATA VALID  
DATA VALID  
DQ (DATA)  
Notes  
11. The software sequence is clocked on the falling edge of CE without involving OE (double clocking abort the sequence).  
12. The six consecutive addresses must be read in the order listed in the Mode Selection table. WE must be HIGH during all six consecutive cycles.  
Document Number: 001-50591 Rev. **  
Page 11 of 15  
 
   
STK11C88  
Part Numbering Nomenclature  
STK11C88 - N F 25 I TR  
Packaging Option:  
TR = Tape and Reel  
Blank = Tube  
Temperature Range:  
Blank - Commercial (0 to 70°C)  
I - Industrial (-40 to 85°C)  
Speed:  
25 - 25 ns  
45 - 45 ns  
Lead Finish  
F = 100% Sn (Matte Tin)  
Package:  
N = Plastic 28-pin 300 mil SOIC  
S = Plastic 28-pin 330 mil SOIC  
Ordering Information  
Speed  
Operating  
Range  
Ordering Code  
(ns)  
Package Diagram  
Package Type  
25  
STK11C88-NF25TR  
STK11C88-NF25  
51-85026  
51-85026  
51-85058  
51-85058  
51-85026  
51-85026  
51-85058  
51-85058  
51-85026  
51-85026  
51-85058  
51-85058  
51-85026  
51-85026  
51-85058  
51-85058  
28-Pin SOIC (300 mil)  
28-Pin SOIC (300 mil)  
28-Pin SOIC (330 mil)  
28-Pin SOIC (330 mil)  
28-Pin SOIC (300 mil)  
28-Pin SOIC (300 mil)  
28-Pin SOIC (330 mil)  
28-Pin SOIC (330 mil)  
28-Pin SOIC (300 mil)  
28-Pin SOIC (300 mil)  
28-Pin SOIC (330 mil)  
28-Pin SOIC (330 mil)  
28-Pin SOIC (300 mil)  
28-Pin SOIC (300 mil)  
28-Pin SOIC (330 mil)  
28-Pin SOIC (330 mil)  
Commercial  
STK11C88-SF25TR  
STK11C88-SF25  
STK11C88-NF25ITR  
STK11C88-NF25I  
STK11C88-SF25ITR  
STK11C88-SF25I  
STK11C88-NF45TR  
STK11C88-NF45  
Industrial  
45  
Commercial  
Industrial  
STK11C88-SF45TR  
STK11C88-SF45  
STK11C88-NF45ITR  
STK11C88-NF45I  
STK11C88-SF45ITR  
STK11C88-SF45I  
All parts are Pb-free. The above table contains Final information. Contact your local Cypress sales representative for availability of these parts  
Document Number: 001-50591 Rev. **  
Page 12 of 15  
 
STK11C88  
Package Diagrams  
Figure 11. 28-Pin (300 mil) SOIC (51-85026)  
NOTE :  
PIN 1 ID  
1. JEDEC STD REF MO-119  
2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH,BUT  
DOES INCLUDE MOLD MISMATCH AND ARE MEASURED AT THE MOLD PARTING LINE.  
MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.010 in (0.254 mm) PER SIDE  
14  
1
MIN.  
3. DIMENSIONS IN INCHES  
MAX.  
0.291[7.39]  
0.300[7.62]  
4. PACKAGE WEIGHT 0.85gms  
*
0.394[10.01]  
0.419[10.64]  
PART #  
15  
28  
0.026[0.66]  
0.032[0.81]  
S28.3 STANDARD PKG.  
SZ28.3 LEAD FREE PKG.  
SEATING PLANE  
0.697[17.70]  
0.713[18.11]  
0.092[2.33]  
0.105[2.67]  
*
0.004[0.10]  
0.0091[0.23]  
0.015[0.38]  
0.050[1.27]  
0.013[0.33]  
0.019[0.48]  
*
0.004[0.10]  
0.0125[3.17]  
0.050[1.27]  
TYP.  
0.0118[0.30]  
51-85026-*D  
51 85127 *A  
Document Number: 001-50591 Rev. **  
Page 13 of 15  
 
STK11C88  
Package Diagrams (continued)  
Figure 12. 28-Pin (330 mil) SOIC (51-85058)  
51-85058-*A  
Document Number: 001-50591 Rev. **  
Page 14 of 15  
 
STK11C88  
Document History Page  
Document Title: STK11C88 256 Kbit (32K x 8) SoftStore nvSRAM  
Document Number: 001-50591  
Orig. of  
Change  
Submission  
Date  
Rev.  
ECN No.  
Description of Change  
**  
2625096  
GVCH/PYRS  
12/19/08  
New data sheet  
Sales, Solutions and Legal Information  
Worldwide Sales and Design Support  
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office  
closest to you, visit us at cypress.com/sales.  
Products  
PSoC  
PSoC Solutions  
General  
Clocks & Buffers  
Wireless  
Low Power/Low Voltage  
Precision Analog  
LCD Drive  
Memories  
Image Sensors  
CAN 2.0b  
USB  
© Cypress Semiconductor Corporation, 2008-2009. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of  
any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be used for  
medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its products for use as  
critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress products in life-support systems  
application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.  
Any Source Code (software and/or firmware) is owned by Cypress Semiconductor Corporation (Cypress) and is protected by and subject to worldwide patent protection (United States and foreign),  
United States copyright laws and international treaty provisions. Cypress hereby grants to licensee a personal, non-exclusive, non-transferable license to copy, use, modify, create derivative works of,  
and compile the Cypress Source Code and derivative works for the sole purpose of creating custom software and or firmware in support of licensee product to be used only in conjunction with a Cypress  
integrated circuit as specified in the applicable agreement. Any reproduction, modification, translation, compilation, or representation of this Source Code except as specified above is prohibited without  
the express written permission of Cypress.  
Disclaimer: CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES  
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Cypress reserves the right to make changes without further notice to the materials described herein. Cypress does not  
assume any liability arising out of the application or use of any product or circuit described herein. Cypress does not authorize its products for use as critical components in life-support systems where  
a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress’ product in a life-support systems application implies that the manufacturer  
assumes all risk of such use and in doing so indemnifies Cypress against all charges.  
Use may be limited by and subject to the applicable Cypress software license agreement.  
Document Number: 001-50591 Rev. **  
Revised January 29, 2009  
Page 15 of 15  
AutoStore and QuantumTrap are registered trademarks of Cypress Semiconductor Corporation. All products and company names mentioned in this document may be the trademarks of their respective  
holders.  
 

Compaq Personal Computer 281862 002 User Manual
Conair Scale WW45 User Manual
Desa Tech Gas Heater CGG3324PT User Manual
Digicom Network Router ADSL User Manual
Earthquake Sound Speaker MC6 User Manual
EverFocus Security Camera EI350 User Manual
GE Monogram Trash Compactor ZCGS150PSS User Manual
GE VCR VGN550 User Manual
Global Machinery Company Biscuit Joiner BJ600 User Manual
Global Technology Associates Kitchen Entertainment Center GB 2000X User Manual